Grizzly Mill Hog 4860 – Reconditioned – SOLD

January 4th, 2012

GRIZZLY MILL HOG 4860 – Reconditioned
Equipment number 11-01000-AM

Grizzly Mill Hog 4860 – Reconditioned – Description
– Handling – Left hand
– Strikers – T.C. (New)
– Heavy duty frame
– Infeed opening 20º
– High inertia rotor
– High wear resistant rear and side wall liners (bolt on) (New)
– Four (4) rows of alternating striker bars, continuous spiral
– Twenty (20) striker bars, tungsten carbide (New)
– Flange mounted arbor bearings 615/16″ø (New)
– Solid steel bearing housing
– Heavy duty grate, 2″ (New)
– Two position rolled grate
– Progressive rectangular hole pattern
– Two shear pins c/w holders
– Swing-away anvil, 6″ thick
– Replaceable liner on anvil, 1½” (New)
– Clam shell opening
– Two (2) hydraulic cylinders, Royal
– Mechanical safety lock
– Electrical safety interlocks, upper frame, anvil, grate and rotor motion (New)
– Rotor safety lock
– Zinc bolts and nuts

NOT INCLUDED:
– Drive motor and drive components
– MCC starters, switch gear
– Hydraulic power unit
– Installation, chuting
– Sub base and support steel

VK450 Infeed Conveyor – Reconditioned – SOLD

January 4th, 2012

VK450 Infeed Conveyor – Reconditioned
Equipment #07-2300

– Self-centering
– Heavy duty fabricated support frame –     (Reconditioned)
– Conveyor trough with wear strips – (New)
– Tail sprocket (idler) – (New)
– Head sprocket c/w drive coupling – (New)
– Parallelogram frame – (New) bushings
– Top hold down roll – (Reconditioned)
– Lubrication fixtures in conveyor wear strips
– Conveyor chain c/w hardened barrels and v-flytes – (New)
– Head and tail shaft bearings – (New).
– Two (2) Hydraulic lift cylinders
– Accumulator, hoses, flow control valve – (New)
– Hydraulic valve – (New)
– Photo eye – (New)
– Handing – Left
– Drive not included
– HPU not included

Most Recent Equipment Sold

August 29th, 2011

The following item was just recently sold: 

– One (1) only Reconditioned Grizzly Mill Hog 4860 – Right hand drive.
  Equipment number 11-01200-AM 

Call Anders Machinery at 604-515-7113 for more details.

Reconditioned – Bruks Drum Chipper 802CS – SOLD

April 1st, 2011

Bruks Drum Chipper 802CS – Reconditioned
Equipment number 11-00200-AM
Bulletin – Bruks 802CS Chipper-Rebuilt

Arranged for right hand drive, drop feed, bottom discharge, and complete as follows:

  • Factory Reconditioned
  • One (1) reconditioned rotor assembly (31″ diameter) with shaft mounted in self-aligning “SKF” spherical  roller bearings (New – housing and bearings two (2))
  • Four (4) knife pockets are re-machined.
  • One (1) rotor mechanical safety lock (New)
  • Four (4) knives (New) with self-releasing feature for quick knife change.
  • Four (4) knife clamps – three (3) New / one (1) reconditioned.
  • Four (4) counter knives (New)
  • One (1) hard surfaced anvil (New)
  • The knife to anvil adjustment is easily done through access doors mounted on  side of the chipper frame.
  • Two (2) B-Loks (New)
  • Heavy fabricated frame, sandblasted, reconditioned, painted.
  • Top hood with large hinged access door for easy knife change.
  • Chip length adjustable from 5/8″ to 1 1/4″.
  • Knife setting jig and knife angle gauge (New)
  • Electrical safety interlocks
    • o Rotor motion – (New)
    • o Hood open – (New)
  • On-machine wiring to common J-box – (New)
  • Common sub-base for chipper and motor slide base (used / existing)

Rebuilt 27″ Kodiak Rotor – SOLD

January 26th, 2010

This rotor was stripped down and rebuilt from the ground up by a Valon Kone service rep and using all OEM parts from Valon Kone. The Kodiak Rotor can be retrofitted into different size frames to make a combination debarker. For example if you have a 22″ modules, you can put in a 27″ rotor. The 22″ modules will open to 25″ so in affect you would have a 25″ debarker. Call for details and information.

[nggallery id=5]

Kodiak 27″ Rotor Description